Same Day Shipping
On many popular products
Showing 1–12 of 171 results
Never lose or misplace vital cables again. Protect your assets by securing the interconnect cable to its related equipment. Having medical cables and equipment tethered ensures your readiness to connect every time! This 16-piece kit allows you to safe guard FOUR essential cables and includes cable leashes with adhesive tab ends, set screws, hex wrenches and alcohol swabs. *Interconnect adapters shown in image sold separately.
Connects the Physio-Control and Zoll Medical defibrillator outputs to CRM Pacer Programmer cables.
This unique Operating Room Boom Cabling System uses the surgical equipment booms to connect the anesthesia device to peripheral monitors. The kit includes 100 feet of cable which runs overhead from one surgical boom to another remote boom arm. Also included are two custom engraved Thermoplastic Duplex Cover Plates which are color coded for signal identification. This system requires a device specific MAGUIRE 410 Series Anesthesia monitor cable, purchased separately. Also purchased separately are the accessory cables which connect the remote wall jacks to your additional monitors such as a defibrillator, balloon pump, ultrasound, continuous cardiac output monitor, and similar monitors. Additional remote boom wall plates with cable are available and easily expand the system. Click here for an image of this unique system installed in the CVOR.
Remote end of 414 Series OR Boom Cabling System for parallel connection. Product enables additional remote drops at the surgical boom arm. Kit includes one Thermoplastic Duplex Cover Wall Plate with four 1/4″ two circuit isolated phone jack outputs. Three are dedicated to ECG signal and one to invasive pressure, IBP. Also included are 50 feet of shielded plenum grade cable with wiring instructions. Click here for an image of this unique system installed in the CVOR.
i cable ECG. 1/4″ phone plug output from the Philips monitor or Maquet-Datascope balloon pump to the Zoll R, X and M series defibrillator ECG input. Also from the Philips monitor to the balloon pump input or ultrasound, AAMI 6 pin ECG input. Compatible with MAGUIRE 257 Series Multipliers or MAGUIRE 414 Series Boom Cabling System, each designed to deliver synchronized waveforms and simultaneous signal transfer onto multiple device displays. Learn how these low cost products simplify patient setup, reduce cable clutter and enhance any physiologic monitoring system.
i cable Nurse Call. 4 pin Hirose normally open alarm output of the Puritan Bennett 700, 740, 760, 840 or 980 series ventilator to a 1/4″ two circuit right angle phone plug. This device alarm cable is compatible with the Maguire Device Alarm Input Multiplier, which expands the headwall jack to allow simultaneous monitoring of up to three devices.
i cable Nurse Call Multiplier. Normally open alarm input at headwall jack (1/4″ phone plug ) expanded to be three parallel 1/4″ phone jacks. Use to increase the number of connected devices at the headwall, turning the average room into a more intensive care unit! This product is compatible with normally open device alarm cables.
i cable ECG. 1/4″phone plug output of the Philips monitor or balloon pump to the LifePak defibrillator LP12, LP15, LP20, LP20e with code management module, 12 pin ECG input. Compatible with MAGUIRE 257 Series Multipliers or MAGUIRE 414 Series Boom Cabling System, each designed to deliver synchronized waveforms and simultaneous signal transfer onto multiple device displays. Learn how these low cost products simplify patient setup, reduce cable clutter and enhance any physiologic monitoring system.
i cable Nurse Call. 616 jack normally open alarm output of Maquet Servo-i, Servo-n, Servo-s and Servo-U ventilator to a 1/4″ two circuit right angle phone plug. This device alarm cable is compatible with the Maguire Device Alarm Input Multiplier, which expands the headwall jack to allow simultaneous monitoring of up to three devices.
i cable Nurse Call. 1/4″ phone plug three circuit alarm output of a Respironics V-60, V-200, V-1000 or Esprit series ventilator to the central station alarm monitoring system input, 1/4″ two circuit phone plug. An integrated switch allows a selection between ‘normally open or ‘ normally closed‘ system protocols. This device alarm cable is compatible with the Maguire Device Alarm Input Multiplier, which expands the headwall jack to allow simultaneous monitoring of up to three devices.
i cable Nurse Call. RJ11 normally open alarm output of Viasys/Pulmonetics LTV Series and Carefusion Enve ventilators to a 1/4″ two circuit right angle phone plug. This device alarm cable is compatible with the Maguire Device Alarm Input Multiplier, which expands the headwall jack to allow simultaneous monitoring of up to three devices.
i cable Nurse Call. DB15 normally open alarm output of Hamilton G5 ventilator to a 1/4″ two circuit right angle phone plug. This device alarm cable is compatible with the Maguire Device Alarm Input Multiplier, which expands the headwall jack to allow simultaneous monitoring of up to three devices.